006 FUEL FEED PUMP
· схем в доске: 1
| № | Артикул | Название | Кол. | Примечание |
|---|---|---|---|---|
| 1 | A 000 091 53 01 | ТОПЛИВНЫЙ | 1 | PUMP WITH BRATHER FILTER INSTALLED IN SERIES WITHOUT BREATHER FILTER |
| 2 | A 000 993 09 10 | - ПРУЖИНА | 1 | FOR HAND LEVER |
| 3 | A 000 994 00 41 | - ПРЕДОХРАНИТЕЛЬ | 1 | FOR HAND LEVER |
| 4 | A 000 091 05 07 | - БАЛАНСИР | 1 | |
| 7 | A 000 091 00 21 | - ACHSE | 1 | FOR PUMP LEVER |
| 8 | A 000 091 08 15 | - ПРУЖИНА | 1 | FOR PUMP LEVER |
| 9 | A 000 091 16 15 | - ПРУЖИНА | 1 | |
| 10 | A 000 091 00 36 | - ЗАЩИТНАЯ ПАНЕЛЬ | 1 | |
| 11 | A 000 091 01 15 | - ПРУЖИНА | 1 | FOR OIL PROTECTIVE PLATE |
| 12 | A 000 091 04 28 | - MEMБРАНА | 1 | |
| 15 | A 000 091 04 29 | - ПЛАСТИНА КЛАПАНА | 1 | |
| 16 | A 000 091 01 80 | - ПРОКЛАДКА УПЛОТНИТЕЛЬНАЯ | 1 | FOR VALVE PLATE |
| 18 | A 000 091 07 29 | - ПЛАСТИНА КЛАПАНА | 2 | FOR INTAKE AND EXHAUST VALVE |
| 20 | A 000 091 00 16 | - ТАРЕЛКА ПРУЖИНЫ КЛАПАНА | 1 | FOR EXHAUST VALVE |
| 24 | A 000 091 08 39 | - Сетка | 1 | |
| 25 | A 000 091 06 80 | - Уплотнительная прокладка | 1 | FOR CAP |
| 26 | A 000 091 01 46 | - ПРОБКА | 1 | FOR UPPER PART |
| 30 | A 000 091 03 56 | - ЗАГЛУШКА РЕЗЬБОВАЯ | 1 | FOR UPPER PART |
| 36a | A 000 091 00 85 | - ФИЛЬТР | 2 | AT FUEL FEED PUMP, LOWER PART ONLY VALID FOR REPLACEMENT DELIVERY |
| 37 | A 181 091 00 80 | Уплотнительная прокладка | 1 | BETWEEN FUEL FEED PUMP AND INSULATING FLANGE |
| 38 | A 181 091 00 81 | ФЛАНЕЦ ИЗОЛЯЦИОННЫЙ | 1 | AT FUEL FEED PUMP |
| 39 | A 181 091 00 80 | Уплотнительная прокладка | 1 | BETWEEN INSULATING FLANGE AND INTERMEDIARY FLANGE |
| 42 | A 180 091 01 80 | Уплотнительная прокладка | 1 | BETWEEN INTERMEDIARY FLANGE AND CYLINDER CRANKCASE |
| 43 | A 180 090 01 44 | ФЛАНЕЦ | 1 | AT CYLINDER CRANKCASE |
| 44 | A 180 091 01 50 | - ВТУЛКА | 1 | |
| 45 | A 180 091 00 91 | - Манжета | 1 | |
| 48 | A 180 091 01 08 | ТОЛКАТЕЛЬ | 1 | FOR FUEL PUMP DRIVE |
| 50 | A 000 094 22 06 | SUCTION NOISE | 1 | DAMPER WITHOUT SUPPORTS |
| 51 | A 000 094 25 06 | - COVER WITH GASKET | 1 | |
| 52 | A 000 094 04 79 | - SEAL FOR OVAL FLANGE | 1 | |
| 53 | A 000 094 12 41 | SUPPORT, REAR | 1 | |
| 54 | A 000 094 13 41 | SUPPORT, FRONT | 1 | |
| 55 | A 000 094 03 79 | - GUMMIUNTERLAGE | 2 | |
| 56 | A 000 094 02 79 | - GUMMIUNTERLAGE | 2 | |
| 57 | A 000 094 01 55 | - ЗАМКОВЫЙ БЛОК | 4 | |
| 60 | A 180 070 01 40 | MOUNTING SUPPORT, CONTROL | 1 | FOR SUCTION NOISE DAMPER AT INTAKE PIPE |
| 61 | A 180 072 04 40 | BRACKET | 1 | FOR RELEASE SPRING FOR SUCTION NOISE DAMPER AT INTAKE PIPE |
| 63 | A 180 094 00 91 | RUBBER SLEEVE | 1 | FOR SUCTION NOISE DAMPER AT CARBURETOR |
| 64 | A 180 997 05 81 | GROMMET | 1 | FOR BREATHER AT SUCTION NOISE DAMPER |
| A 001 094 10 02 | SUCTION NOISE | 1 | DAMPER WITH OIL BATH AIR FILTER WITHOUT SUPPORTS EXPORT, SPECIAL REQUEST (TROPICAL DESIGN) | |
| A 000 094 32 06 | - ELEMENT WITH GASKET | 1 | EXPORT, SPECIAL REQUEST (TROPICAL DESIGN) | |
| A 000 094 33 80 | - GASKET | 1 | EXPORT, SPECIAL REQUEST (TROPICAL DESIGN) | |
| A 000 094 14 41 | SUPPORT, FRONT | 1 | EXPORT, SPECIAL REQUEST (TROPICAL DESIGN) | |
| A 000 094 15 41 | SUPPORT, REAR | 1 | EXPORT, SPECIAL REQUEST (TROPICAL DESIGN) | |
| A 000 094 02 79 | - GUMMIUNTERLAGE | 2 | EXPORT, SPECIAL REQUEST (TROPICAL DESIGN) | |
| A 000 094 03 79 | - GUMMIUNTERLAGE | 2 | EXPORT, SPECIAL REQUEST (TROPICAL DESIGN) | |
| A 000 094 01 55 | - ЗАМКОВЫЙ БЛОК | 4 | EXPORT, SPECIAL REQUEST (TROPICAL DESIGN) | |
| A 180 094 00 84 | COMPENSATING SPACER | 4 | EXPORT, SPECIAL REQUEST (TROPICAL DESIGN) | |
| A 000 987 10 36 | резиновый профиль | 1 | 50-MM LONG FOR INSULATING RING, CHOKE CABLE AGAINST SUPPORT, SUCTION NOISE DAMPER ORDER BY THE METER |
Позиций: 49 · подписано на схемах: 39 · колесо — плавный зум в курсор, перетаскивание — пан, двойной клик — зум, клик по артикулу — скопировать.